Troubleshooting

Post to this forum if you are experiencing problems with LibreCAD

Please mention your operating system and LibreCAD version - this will enable us to advise you properly.

Report bugs here:
https://github.com/LibreCAD/LibreCAD/issues

1234 ... 19
Topics (640)
Replies Last Post Views
pin
Raynor42 How to export a drawing in good quality? by Raynor42
8
Raynor42 by Raynor42
pclem Print Standard font 3 issue by pclem
2
pclem by pclem
Nate spline isn't closed when opening DXF in other apps by Nate
0
Nate by Nate
mdimauro16 Extra text upon opening DXF file by mdimauro16
5
dxli by dxli
mdsimon58 No puedo ver los textos. by mdsimon58
4
flywire by flywire
bnickers Problems with displaying dimension text (or just text in general?) by bnickers
4
Darren by Darren
Sam Barns Can't see drawing in print preview by Sam Barns
20
flywire by flywire
Dobro Fillet command by Dobro
9
Dobro by Dobro
AHG Screen cuts off lower part of characters in Status bar by AHG
10
flywire by flywire
AHG Problem of snapping to last relative point rather than desired objects. by AHG
3
LordOfBikes by LordOfBikes
Adeildo Congelamento de tela by Adeildo
3
dxli by dxli
Kohqow No lines are displayed by Kohqow
2
Kohqow by Kohqow
shelly.evans Angle is not correct by shelly.evans
2
shelly.evans by shelly.evans
numra99 PDF Export is Empty by numra99
5
dxli by dxli
Juraj Cirkle by Juraj
6
Juraj by Juraj
PAB Will not select entities within a command by PAB
4
PAB by PAB
Andrdew Gentry Reopen the file and it is blank by Andrdew Gentry
9
dellus by dellus
Andrdew Gentry Change drawing layers by Andrdew Gentry
1
dellus by dellus
mcyphert empty box on dimension lines by mcyphert
2
mcyphert by mcyphert
KaptajnKlo Extra lines on DXF drawing by KaptajnKlo
3
KaptajnKlo by KaptajnKlo
jon100p DXF saved in LibreCAD not opening in AutoCAD or TrueView by jon100p
0
jon100p by jon100p
MarkHamann Discover current attributes of line by MarkHamann
2
MarkHamann by MarkHamann
flytyer96 Offset by flytyer96
0
flytyer96 by flytyer96
tomma Ortho mode in command line by tomma
12
sergi0s by sergi0s
Auric_Goldfinger how can individual areas be printed out of a large drawing by Auric_Goldfinger
1
dxli by dxli
BenDragon81037 LibreCAD not finding entity by BenDragon81037
0
BenDragon81037 by BenDragon81037
jim.macp Drawing is blank when reopening by jim.macp
0
jim.macp by jim.macp
Rahooty Printer configuration by Rahooty
1
flywire by flywire
Lucio Pannitteri section by Lucio Pannitteri
1
dxli by dxli
SG1stLady Dividing a line keeps glitching by SG1stLady
2
SG1stLady by SG1stLady
SmallCar Circles from the Command Line by SmallCar
6
dellus by dellus
Priscillia IMPORTANT SVP Message d'erreur by Priscillia
1
perepujal by perepujal
AbingdonRail Select Tool on Macbook Trackpad by AbingdonRail
0
AbingdonRail by AbingdonRail
Werner Instal New version by Werner
1
dellus by dellus
María maría by María
1
flywire by flywire
1234 ... 19